A tour of the editor
The Building Model editor is where you draw and change a model. This page says what you see and where the main tools are. Names in bold are the words on the screen.
Open a model from My models to get here (see Getting started). Everyone with the model open sees each other's changes live.
The screen
- The ribbon across the top holds the tools, sorted into tabs.
- The left sidebar lists the model's views and sheets and what the open view shows. Drag its right edge to make it wider.
- The view in the middle: a plan, the 3D model, a drawing or a sheet.
When you open a model shared with you to view, the bar above the editor shows View only, and tools that change the model are off. Hover a tool that is off to read why.
The ribbon
The tabs are Model, Annotate, Modify, Views, Sheets and Manage, plus a tab for each trade add-on, such as Architecture, Mechanical, Electrical and Plumbing.
- Select sits at the left of every tab.
- Undo and Redo sit at the right on every tab.
- Find a tool (or press
/) searches every command on every tab, opens its tab and runs it. Use it when you know what you want but not where it lives. - The arrows at the far right fold the ribbon to one row of icons, and back.
- A group with more than five tools puts the rest under More.
- When you select something, a tab for it appears and opens by itself: Part for a part, Duct run or Pipe run for a run, Branch for a branch, and Selection when you select several things.
Every trade tab has the same sections in the same order, after Select: Create, Connect, Analyze, Design and Documents. A tab leaves out a section it has nothing for. Learn one trade tab and you can find your way around the next.
Views: plan, 3D and sheets
The Views and sheets list in the left sidebar is how you move around. At the top are two live views of the whole model:
- 3D model: everything, live, in 3D.
- Top-down plan: all levels, looking down.
Below them are your saved views, grouped as Floor plans, Ceiling plans, Sections, Elevations, 3D views, Detail views and Schedules, then Sheets. Click one to open it. Each saved view and sheet has a menu with Rename…, Duplicate (views) and Delete….
To make a new view, press + beside Views and sheets, or use Views › New view. The choices are:
- Floor plan for a level
- Ceiling plan
- Section (draw a cut line)
- Elevation (draw view plane)
- 3D view
- Detail view (drawing-only), for lines, text and dimensions only
- New schedule…
- Diagrams drawn from the model, such as One-line diagram and Riser diagram
The Views tab also has Graphics (Lines and colours, What this view shows, Linked model look) and Crop, which works in 3D: Crop view, Crop to selection, Reset crop and Align crop box. On the Model tab, Display has Fit (F), Lift the roof off for the 3D model, and Orthographic (5) for a parallel 3D view.
Model tools work in plans, sections and the 3D model. On a sheet, double-click a plan or section to edit it there.
Levels
Parts and runs sit on a level. A blank model starts with one.
To add one, use Model › Datum › Add level. The Add a level dialog asks for a Name and a Floor (ft) height, and lists the levels you already have. It can also take the height from the model:
- Pick a surface: click a roof or floor to take its height.
- Use the architect's levels, when a linked model has them.
Typing the name of a level you already have moves that level, with everything on it. You can undo adding a level.
Show levels draws each level in the 3D model as a faint outline with its name and height. In the sidebar, Show has a Level (3D model) choice to show one level or All levels.
Placing parts
Press Place part on the Model tab (key P). The left sidebar shows Place a part:
- Search parts, or pick a category.
- Choose the Level and the Height (ft).
- Click a part, then click in the view to place it.
Press the × (Stop placing) or Esc when you are done. With a part selected, the Part tab has Rotate 90°, Rotate −90°, Move (M), Edit type (values every part of that type shares) and Delete….
Routing duct and pipe
Press Route duct (key D) or Route pipe on the Model tab. The left sidebar shows the route settings:
- System: an existing system in this model, or a new one with a name. Starting on an existing run continues its system.
- Size: for duct, Rectangular (Width (in), Height (in)) or Round (Diameter (in)); for pipe, a Pipe type, or Size (in) and Material.
- Level and Height (ft).
- For pipe, Slope and which way it Falls: Toward the main, Down as drawn or Up as drawn.
- Inherit from a pipe or part takes the height, size, system and slope of what you click.
Click a connector, a run or a point to start, then click each point. While you route, the Route tab has:
- Rise 1 ft (
]) and Drop 1 ft ([). - Elbow type, Takeoff type, and Offset around (
O), which takes the leg over a beam, pipe or wall in the way and back down. - Finish here (Enter) and Cancel (Esc). Cancel saves nothing.
Sizing
Select a run and use Resize on its Duct run or Pipe run tab to change its size or shape; the fittings follow, with transitions where it meets another size. Split (S) cuts a straight run where you click, so you can resize one stretch. Select several runs and Resize on the Selection tab gives them all a new size in one edit.
The trade tabs size whole systems:
- Mechanical › Analyze › Size ducts sizes every duct run of the air systems you pick from the airflow it carries. You see each change first, and it is one undo.
- Plumbing › Analyze › Auto-size. Off, every pipe is checked and sizes are suggested; nothing changes until you accept. On, suggested sizes apply as you model.
Spaces and rooms
Spaces are the rooms and zones you design for. Open them from the Plan group on the Model tab or a trade tab: Spaces, Room from walls (hover inside a room's walls, then click) and Find rooms from walls (you accept or reject each room before anything is saved). Split space draws a line wall to wall across a room to give it sub-rooms.
The Spaces panel in the sidebar has Draw space, Add drawing (an architect's PDF or picture to trace over; set its scale first), Make from rooms and a Rooms from walls menu. Spaces are drawn on the level of the open floor plan.
Schedules
A schedule lists items from the model as a spreadsheet. It reads the model live, and changes you type in it go back into the model.
- New schedule… (on most tabs, and in the + menu) asks What it lists, a Name and the columns, and can place it on a sheet.
- Open a schedule opens one you have.
- Manage › Library holds the firm's shared calculations, fields and schedule templates.
Notes, tags and dimensions
The Annotate tab works on an open sheet, plan, section or detail view. It has Dimension, Detail line, Revision cloud, Text (a note; drag its grips to re-wrap), Tag, Keynote, Callout, Tag all and Tag styles.
- Tag labels an element with its size, mark or CFM.
- Tag all tags every untagged duct, pipe, terminal, fixture and piece of equipment in the view. Undo removes them all.
- Keynote gives elements a key and a keynote tag. A sheet's keynote list (Sheets › Live table › Keynote list) shows the words.
Sheets
Make a sheet with Sheets › New sheet or + › New sheet, then drag views onto it. The Sheets tab has:
- Title block: the sheet number, name and title block fields.
- Arrange views: rows or a grid inside the border.
- Revisions: the sheet's revision table.
- Project info: name, number, address, people, issue date and status, filled in once and printed on every sheet.
- Print set: the whole set to one PDF, a page per sheet, at scale.
- Issue set: checks the set against its last print, adds the revision row and issues it.
- Export IFC: the saved model as an IFC 4.3 file for other BIM and coordination software.
Print set… and Issue set… are also under Sheets in the sidebar.
Branches and versions
Main is the model everyone shares. A branch is a copy you can try changes in without touching Main. A version is a saved point you can come back to.
Branches. The Branch: Main button above the model lists the branches. New branch… asks for a Name and what to Start from (now, or a saved version). On a branch, a banner shows it at all times with Back to Main and Close branch…. Closing a branch stops anyone editing it; Main is not changed. Show Main beside compares the branch with Main.
To bring a branch's changes into Main, use Propose merge to Main. Main changes only when the approved parts land. If the model server does not merge branches yet, the editor says so.
Versions. Manage › Versions & sign-off › Versions lists saved versions and issued sets. Type a name (for example "Before VE") and press Save version. New branch from this version starts a branch there.
You need Can edit access to start branches and save versions.
Keys
These are the keys the tooltips name.
| Key | What it does |
|---|---|
/ | Find a tool |
P | Place part |
D | Route |
M | Move |
B | Box select |
S | Split a run |
F | Fit everything in view |
5 | Orthographic on or off (3D) |
] / [ | Rise / drop 1 ft while routing |
O | Offset around, while routing |
| Enter | Finish the route here |
| Esc | Stop the tool, or deselect |
| Del | Delete the selection (asks first) |
| Ctrl+Z / Cmd+Z | Undo |
| Shift+Ctrl+Z / Shift+Cmd+Z | Redo |
Next: Connect Claude or another assistant to have an assistant build and change the model by script.